A-Plus Floor Master® Chlorinated Rubber Based Floor Coating is a modified CRB coating formulated to provide superior outdoor durability and extreme abrasion resistance. It is best used for exposed outdoor sports flooring where frequent exposure to sun, weathering, chemicals, and high friction occurs.
☑Ideal for Sports Floor Coating
☑ Chlorinated Rubber Based
☑Superior Resistance to UV Exposure, Chemicals, and Weathering
☑For Interior and Exterior Use
☑Excellent Abrasion Resistance, Easy to Maintain
Specifications
Principal Uses: Ideal for heavy foot traffic and highly exposed areas such as outdoor sports flooring, parking and open spaces, playgrounds, traffic markings, and many more.
Sheen: Semi-Gloss
Coverage:
First Coat: 16-20sqm per gallon
Second Coat: 20-25 sqm per gallon
Surface Dry: 1 hr
Recoat Interval: 2-3 hrs
Dry Through: Overnight curing time for light traffic 3-7 days to achieve full strength
Thinning: Up to 1/2L to 1L A-Plus Floor Master® Reducer per gallon paint
Application: Brush, Roller, or Spray
Packaging: 4L, 16L
Shelf Life: One year when stored in dry cool conditions
Surface Preparation & Precautions
Concrete Substrate:
- Ensure proper surface preparation by removing any oil and dirt by detergent cleaning.
- Sand or use a mechanical floor grinder with large grit to roughen and level the surface, allowing the paint enhanced grip and adhesion.
- Surface must be completely dry and clean before application of paint.
- If previously painted, strip off all paint to bare substrate with A-Plus Supertanggal® Paint Remover.
- MIX WELL BEFORE USING.
- To repair large concrete surface imperfections, use either of the following:
– A-Plus Procrete® Low Viscosity Construction Epoxy – used for patching medium-sized concrete imperfections covering a large area.
– A-Plus Procrete® High Viscosity Construction Epoxy – used for patching larger-sized concrete imperfections covering smaller areas.
Metal Substrate:
- Remove dust, dirt, grease, oil, wax and other foreign matter by sanding and using a rag soaked in paint thinner.
- For repainting, use A-Plus Supertanggal® Paint Remover to strip off old paint film to bare substrate then remove oil and grease by solvent cleaning followed by scuff sanding. To remove rust, wire brush or strip affected areas while applying A-Plus® Rust Converter. Let it sit for 10 – 15 minutes before washing off surface thoroughly with water, letting it dry before applying paint.
- Primer should be applied immediately upon drying of the surface before rust sets in.
Painting Procedure
For New Concrete:
- Surface should be clean and dry, free from dust, dirt and other foreign contaminants. For repainting concrete, strip off loose/old paint to bare substrate.
- First coat will serve as primer/sealer. Apply 1 coat of A-Plus Floor Master® Chlorinated Rubber Based Floor Paint using either a brush, roller, or spray. Allow to cure for at least 1 hour before proceeding with the topcoat.
- Topcoat: At least 1-2 coats A-Plus Floor Master® Chlorinated Rubber Based Floor Paint using either a brush, roller, or spray.
- Allow the surface to cure overnight before subjecting to light traffic. Allow the surface to cure for at least 3-7 days before subjecting to heavy traffic.
For Metal Substrates:
- Surface should be clean and dry, free from dust, dirt and other foreign contaminants. For repainting concrete, strip off loose/old paint to bare substrate.
- Primer: Apply at least 1 coat of Glazer Galva-Plus® Epoxy Primer. Allow to fully cure before proceeding with the topcoat.
- Topcoat: At least 2 coats A-Plus Floor Master® Chlorinated Rubber Based Floor Topcoat using either a brush, roller, or spray.
- Allow the surface to cure overnight before subjecting to light traffic. Allow the surface to cure for at least 3-7 days before subjecting to heavy traffic.
Color Swatches
-
9318
ENDURO WHITE -
9322
FACTORY BEIGE -
9342
INDUSTRIAL RED -
9345
VELVET RED -
9332
STURDY ORANGE -
9325
INDUSTRIAL YELLOW -
9355
COOL GREEN -
9358
CLASSIC GREEN -
9365
COOL BLUE -
9368
CLASSIC BLUE -
9385
LIGHT GRAY -
9388
MEDIUM GRAY
